ZyXEL foutmeldingen (gevorderd)
referentie Z037B
Foutmeldingen kunnen worden gebruikt om er achter te komen waarom iets niet werkt zoals het zou moeten werken.
De onderstaande meldingen zijn van toepassing bij DSL routers (zoals de 2602 (oud model), 650 en 761 met de mogelijkheid tot het opzetten van een Telnet sessie.
Voor het gebruik moet eerst via de CLI het volgende commando worden gebruikt:
(CLI wordt uitgelegd in de Telnet link hierboven)
Copyright (c) 1994 - 2002 ZyXEL Communications Corp.
ras> sys log disp i
|
Het weergeven van de foutmeldingen kan worden weergegeven via Telnet menu 24.3.1
Dit geeft resultaten als:
62 112 PP0a INTL call failed, rnp=576de0, code = -3022
|
waarbij de code achteraan staat,
Main Error Codes
--------------------------------------------------------------------------------
-3000 remote node is connecting
-3001 configured incoming call only, outgoing call fails
-3002 configured outgoing call only, incoming call fails
-3003 packet is filtered
-3004 no iface
-3005 no channel available
-3006 call request fail
-3007 remote node is waiting call back
-3020 call dial fail
-3022 filter groups are mixed, so call is not allowed
-3023 received unexpected event
-3024 state timeout
-3025 waiting RADIUS authentication
-3026 RADIUS call back fail
-3028 the node is not found
-3029 the node is inactive
-3030 dial fail
-3031 no budget
-3032 radius authentication fail
-3033 CLID is required
-3034 CLID can not be found
-3035 an outgoing call has already been placed for this remote node
-3036 call is blocked
-3037 invalid phone number
-3038 remote side is busy
-3039 no carrier
-3040 no dial tone
-3041 remote node is not active
-3042 no answer received
-3043 dial timeout
-3045 redial stopped
-3046 redial no number
-3047
-3048 remote node is not L2TP enabled or supported
--------------------------------------------------------------------------------
-3000
Message: PINI ERROR netMakeChannDial: err=-3000, rn_p=576de0
Meaning: remote node is connecting already. (rn_p refers remote
node point, it may change for different version, and different
remote node number)
Solution: ask remote node to dial to you, then if you drop, you can dial;
or reboot.
-3001
Message: PINI ERROR netMakeChannDial: err=-3001, rn_p=576de0
Meaning: remote node call direction is configured as incoming only.
Solution: change the call direction to outgoing or both.
-3002
Message: PINI ERROR netMakeChannDial: err=-3002, rn_p=576de0
Meaning: remote node call direction is configured as outgoing only.
Solution: change the call direction to both or incoming.
-3003
Message: PINI ERROR netMakeChannDial: err=-3003, rn_p=576de0
Meaning: call failed, packet is filtered.
Solution: clean the filter set and reboot.
-3004
Message: PINI ERROR netMakeChannDial: err=-3004, rn_p=576de0
Meaning: call failed due to no iface.
Solution: reboot or drop one line.
-3005
Message: PINI ERROR netMakeChannDial: err=-3005, rn_p=576de0
Meaning: call failed, both channels are down or occupied.
Solution: initilize the ISDN line or drop one line.
-3006
Message: PINI ERROR netMakeChannDial: err=-3006, rn_p=576de0
Meaning: call request failed.
Solution: check the configuration.
-3007
Message: PINI ERROR netMakeChannDial: err=-3007, rn_p=576de0
Meaning: remote node dial to you and wait you call back.
Solution: do nothing, it should be information.
-3020
Message: PINI ERROR netMakeChannDial: err=-3020, rn_p=576de0
Meaning: call dial fail.
Solution: check resource and configuration.
-3022
Message: PINI ERROR netMakeChannDial: err=-3022, rn_p=576de0
Meaning: filter groups are mixed, so call is not allowed.
Solution: clean the filter set and reboot.
-3023
Message: PINI ERROR netMakeChannDial: err=-3023, rn_p=576de0
Meaning: received unexpected event.
Solution: do nothing, it should be information.
-3024
Message: PINI ERROR netMakeChannDial: err=-3024, rn_p=576de0
Meaning: state dial timeout.
Solution: do nothing, it should be information.
-3025
Message: PINI ERROR netMakeChannDial: err=-3025, rn_p=576de0
Meaning: waiting RADIUS authentication.
Solution: do nothing, it should be information.
-3026
Message: PINI ERROR netMakeChannDial: err=-3026, rn_p=576de0
Meaning: RADIUS call back fail
Solution: do nothing, it should be information.
-3028
Message: PINI ERROR netMakeChannDial: err=-3028, rn_p=576de0
Meaning: can not find the remote node.
Solution: check configuration.
-3029
Message: PINI ERROR netMakeChannDial: err=-3029, rn_p=576de0
Meaning: the node is not active.
Solution: check the configuration of the remote node.
-3030
Message: PINI ERROR netMakeChannDial: err=-3030, rn_p=576de
Meaning: dial fail.
Solution: do nothing if it happens once for a while; check the line if
keep receiving this message.
-3031
Message: PINI ERROR netMakeChannDial: err=-3031, rn_p=586de0
Meaning: can not dial due to no budget.
Solution: reconfigure Menu 11 remote node profile - Allocated Budget.
-3032
Message: PINI ERROR netMakeChannDial: err=-3032, rn_p=526de0
Meaning: RADIUS authentication.
Solution: check the configuration in Menu 23.2.
-3033
Message: PINI ERROR netMakeChannDial: err=-3033, rn_p=596de0
Meaning: dial failed due to remote side CLID= required or dial-in user
CLID=required.
Solution: enter correct CLID number in remote node or in dial-in user
setup.
-3034
Message: PINI ERROR netMakeChannDial: err=-3034, rn_p=572de0
Meaning: CLID can not be found
Solution: enter the correct CLID.
-3035
Message: PINI ERROR netMakeChannDial: err=-3035, rn_p=576de0
Meaning: call conflict, receive RING after an outgoing call has already
been placed for this remote node.
Solution: do nothing, it should be information.
-3036
Message: PINI ERROR netMakeChannDial: err=-3036, rn_p=576de0
Meaning: call is blocked due to it's in the blacklist.
Solution: remove it from blacklist in Menu 24.9.2.
-3037
Message: PINI ERROR netMakeChannDial: err=-3037, rn_p=376de0
Meaning: invalid phone number.
Solution: check phone number in SMT.
-3038
Message: PINI ERROR netMakeChannDial: err=-3038, rn_p=576ae0
Meaning: dial fail due to remote side is busy.
Solution: wait until remote side is available.
-3039
Message: PINI ERROR netMakeChannDial: err=-3039, rn_p=526de0
Meaning: dial failed due to no carrier.
Solution: check the ISDN line or reboot.
-3040
Message: PINI ERROR netMakeChannDial: err=-3040, rn_p=576de0
Meaning: no dial tone.
Solution: check the phone line.
-3041
Message: PINI ERROR netMakeChannDial: err=-3041, rn_p=576de0
Meaning: remote node is not active.
Solution: active the remote node.
-3042
Message: PINI ERROR netMakeChannDial: err=-3042, rn_p=576de0
Meaning: no answer received.
Solution: check whether the phone number configured correctly.
-3043
Message: PINI ERROR netMakeChannDial: err=-3043, rn_p=276de0
Meaning: dial timeout.
Solution: change the timeout value.
-3045
Message: PINI ERROR netMakeChannDial: err=-3045, rn_p=576de0
Meaning: redial stopped.
Solution: do nothing, it should be information.
-3046
Message: PINI ERROR netMakeChannDial: err=-3046, rn_p=76de0
Meaning: no number available to make a call again.
Solution: do nothing, it should be information.
-3047
Message: PINI ERROR netMakeChannDial: err=-3047, rn_p=56de0
Meaning: first call to peer with CLID authenticated and the peer is
obtained CLID but PPP is not up yet, second call to the peer
with same CLID is coming.
Solution: using different CLID.
-3048
Message: PINI ERROR netMakeChannDial: err=-3048, rn_p=576de0
Meaning: remote node is not L2TP enabled or supported.
Solution: change remote side configuration - enable L2TP if possible.
--------------------------------------------------------------------------------
Other Error Codes
35. Message: PINI ERROR LoopBack Test Fail: -4
Meaning: isdn loopback test fail due to no link or wrong number.
Solution: check the Menu 2 setting and reintialize ISDN line.
36. Message: PP09 ERROR Inet SUA: cannot get IP addr from server.
Meaning: Server did not assign IP address to you when you are using SUA.
Solution: request server assign IP address to you if you need use SUA.
37. Message: PNET ERROR iproute SUA O/G: No port for source A0659522,264
Meaning: outgoing call failed since the port for the source is not in the SUA table.
Solution: too many users on the LAN.
38. Message: PP09 WARN Discard unknown network protocol 0x802B.
Meaning: the peer using the different network protocol. (WARN - warning log)
Solution: not a problem.
39. Message: PP0a WARN CHAP : login to remote failed, please check user/pswd.
Meaning: login to the remote node failed.
Solution: check the login name and password.
40. Message: PP09 WARN Local IP mismatch, proposed 1.1.1.1 neg'd 209.24.163.33
Meaning: peer wants to assign IP address to you which is different from Menu 3.2 local IP address.
Solution: use SUA to accept the peer assigned IP address.
41. Message: WARN ppp CCP Stac seq error; recv'd 0x67 exp'd 0x81
Meaning: received compression packet not matching with the expected number.
Solution: it is not a problem.
42. Message: PP08 INFO CALL REJ: ch<5ba788> CLID not matched.
Meaning: CLID number is not match the remote node CLID. (INFO - information log)
Solution: change to correct CLID number.
43. Message: Tracelog type 21180 level 1
Meaning: tracelog type xxx: refers the type of information will be displayed. 21180 - L2TP
bit 0 -- error log trace bit 1 - kernel trace bit 2 - memory
bit 3 -- mbuffer bit 4 - Stdio bit 5 - ndis LAN packet
bit 6 - LAN packet bit 7 - WAN packet bit 8 - IP protocol
bit 9 - IPX protocol bit 10 - Bridging protocol bit 11 - AppleTalk protocol
bit 12 - ppp protocol bit 13 - application bit 14 - SPT
bit 15 - connection manager bit 16 - event manager
bit 17 - L2TP protocol
level xx: refers the information contents will be displayed, lower level - less contents. Default is level 5.
44. Message: CheckSum Error 1
Meaning: 1. Download wrong firmware to the hardware because hardware does not have enough flash memory for this firmware.
Or 2. download fail.
Solution: 1. Use large flash memory for this firmware. 2. Redownload.
45. Message: 9f PNET WARN ppp MP late arrival seq x877 M x0
Meaning: the receiver received a previous packet after it has received a late packet.
Solution: it is not a problem.
46. Message: INFO addCallHistory: Transfer rate 255 is out of defined
values.
Meaning: transfer rate is not in the defined range.
Solution: report to ZyXEL support. (one call history is missed in the call history table).